Search results

I have the same issue with my driver's side door registering as open when it's fully closed. You dont have to take the outer skin off, but the interior door card on the rear door does need to cover off. I believe the sensor that needs to be replaced is 51227291034-10 (this is for the driver's...

Thanks for confirming, would you mind snapping a picture of it, am curious how tight the fitment is! I measured the width difference between the Ecopia and the Momo, and the Momo was about .75 inch wider, and wasn't sure if that was going to clear the suspension components on the inside. I am...

I know I am bumping an old thread, but has anyone tried the Momo 195/55/20 on a regular i3 (non-IS)? Does it fit, require a spacer, etc?

Thank you very much!

Hi, I have a 2016 Rex and when to the tire shop to have tires replaced and discovered that the previous owner had cross threaded most of the wheel studs on the rear driver’s side. How I need to have the wheel hub replaced. I can’t seem to find the part number for this, when I google for it...

I am glad everyone is okay. I am very surprised that at 30-40mph, the only suffered that much damage. There isn’t much above the crash bar to absorb the energy—were you on full brakes just prior to the impact? The i3’s body structure is very impressive, but looks like none of it saw any...

Does that device feel warm to you when you are charging? Some of these smart outlets are not well made and can be a fire hazard—is it UL listed, or other carry some sort of safety certification?

Just throw a t-shirt over it? :)

Thanks for the suggestion, I don’t have a lid anymore because my son’s school bag won’t fit with the lid in place, so out it went.

Thanks guys! I started browsing the link above and since the rear seatbelt is under that cover, I was able to find what I needed. In case anyone else needs it: https://www.newtis.info/tisv2/a/en/i01-i3-hat/repair-manuals/72-body-parts-accessories/72-11-seat-belts/1VnXfUKbo7 Thanks again!

Does anyone know how to remove the rear panel in the trunk area, where the trunk light is mounted? Would like to add more lighting but I can’t find any fasteners keeping the panels in, and I am not sure how these newer BMW are out together (my experience has been with a 1980 320i, and 1996...

How was your oil level, and what oil were you using?

I knew the Party did this, but didn’t know how. Thanks for sharing! So how does this work? Slurps data off the CAN bus and sends it back via the GSM modem? Why do you need to connect the module back into itself? Do removing the module disable the car?

The top one opens the door, the bottom one releases the latch on the charger. Don’t yank on it too hard, it looks like it could break easily. https://youtu.be/1lIO8D3vruc

Thanks! Got it working! :)

Yeah, kind of disappointed it’s not sealed. Maybe I will take it in at some point to see if this is a warranty item.

Well, if it is possible, it’s not obvious. I have instead setup a schedule on my charger so that it will only charge the car during that schedule, and charge immediately only requires a single key press on the charger.

If you think it is just the mechanical port that is bad, you can try replacing it? https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F401045215850 Not sure if that is the exact unit for the i3 but similar ones are pretty inexpensive. If it’s on the headunit...

Has anyone taken apart the dash display (not the headunit display, but the one ahead of the steering wheel? There seems to be dust inside mine, not sure if there was a way to clean it. Once you see it... it cannot unseen.

It is reasonable to assume if the pack is the same size, it should work, but a larger pack might require some programming, or the charging module?