Beemer link activated.
But strange, now error is not active and I can switch forward/backward !?!?!?!
I have zilion of errors in memory,
and 5 permanent errors which cant be deleted
Permanent Errors
Date: 6/18/23 21:11:04
Range extender electrical machine electronics
5 errors
CB946A: A-CAN, message (control crash, 0x19B): missing
21DF1C: Signal (Zeit_Tag_Zähler_Absolut [1], 0x328): Invalid value
21DF29: Signal (Distance_Kilometer [5], 0x330): Invalid value
21DF23: Signal (Steuerung_Abschalt_EKP_Crash [1], 0x19B): Invalid value
21DE05: REME operating status: assembly mode active
Info Memory
Date: 6/18/23 20:50:53
Crash Safety Module
1 error
01A040: VSM_EVENT_VEHICLESTATE
All-round vision camera
3 errors
8BAC78: PIA_E_IO_ERROR
800B9D: ECU Over Temperature
800BD6: ECU_RESET_REASON
Battery management electronics
3 errors
070001: DM_QUEUE_DELETED
21F16D: HVS: U / i sensor - unexpected reset
21F282: HVS: Battery aging: online capacity determination out of date
Range extender electrical machine electronics
16 errors
CB946A: A-CAN, message (control crash, 0x19B): missing
21DF1C: Signal (Zeit_Tag_Zähler_Absolut [1], 0x328): Invalid value
21DF29: Signal (Distance_Kilometer [5], 0x330): Invalid value
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DF02: Signal (actual_voltage_highvolt storage, 0x112): invalid value
2
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DF02: Signal (actual_voltage_highvolt storage, 0x112): invalid value
21DF02: Signal (actual_voltage_highvolt storage, 0x112): invalid value
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
21DDD0: REME Inverter, power-reduced operation: temperature threshold exceeded
Central Gateway Module
9 errors
100600: Flexray protocol startup time is too high
100601: Unexpected asynchronous state on Flexraybus
100604: A FlexRay error has occurred
101030: KL15 attempt without success
100100: Contact to FZM slave lost
100104: HW Weckgrund ZGW
100300: Commissioning could not be carried out because TAS is already busy
100203: DM software error info warning
100204: Message monitoring: no system context signal
Charging interface module
5 errors
001001: Signal (Zeit_Sekunde_Zaehler_Relativ, 0x328): invalid
80557E: Error could not be sent after the maximum number of attempts
8BAC73: NVM_E_REQ_FAILED
E89400: Message (vehicle status, 0x3A0) is missing
3
805543: PLC_ERROR_REASON
Convenience charging electronics
3 errors
001001: DM_EVENT_ZEITBOTSCHAFTTIMEOUT
C90402: Error could not be sent after the maximum number of attempts
21E6EB: Terminal 30 emergency low
Electrical machine electronics
8 errors
22280B: HV power management: switch-off request cat 4
E89400: Message (vehicle status, 0x3A0) is missing
22282A: Checkcontrol 244: Apply the brake to engage gear!
C90402: Error could not be sent after the maximum number of attempts
223AAD: UCX, FIS_21E606, 0x21E606
22282E: Checkcontrol 557: Secure the vehicle against rolling away!
22282D: Checkcontrol 394: Possibly malfunctioning selector lever!
223AAB: UCX, FIS_21E633, 0x21E633
Hybrid pressure refuelling electronic control unit
2 errors
1D0002: Error could not be sent after the maximum number of attempts
1D0001: Message (vehicle status, 0x3A0) is missing
Optional equipment system
4 errors
030807: FAS - functional deactivation
03081F: FAS - front protection - acute warning triggered
030850: FAS - front protection - braking stage 1 triggered
4
482EBB: IPDUM_E_TRANSMIT_FAILED
Dynamic stability control
1 error
4809C0: Local power supply - control unit reset
Parking maneuvering assistant
4 errors
803296: RVC active without activation
803359: WDGM_E_SET_MODE
80335D: PIA_E_IO_ERROR
8032A0: PMA termination functional without CCM
Electromechanical power steering
2 errors
482286: NVM_E_REQ_FAILED
4822C6: Assist-Firewall-Touched
Hi-fi amplifier
3 errors
B7F4F0: Front left speaker channel error (mid-range speaker, if controlled separately)
B7F4F1: Fault in the front right loudspeaker channel (mid-range speaker, if activated
separately)
B7F4F5: Error loudspeaker channel at the rear left (mid-range speaker, if activated
separately)
Body Domain Controller
19 errors
03009B: FH BF: Reversing in emergency mode
400030: EWS communication Primary: timeout redundancy
5
400031: EWS communication secondary: Timeout redundancy
4002FF: Too frequent writing on the same EEPROM block
804000: Reset for unknown reason
804001: Reset due to start-up
804002: Reset by external
804029: NVM_QUEUE_EEPROM
80402C: NVM EEPROM driver error
8040BC: IBS Wakeup: implausible wake-up signal
8040C4: KL30F: Reset request due to bus alarm clock
8040C7: Intelligent battery sensor (IBS): recharge limit reached
8040CB: Terminal 15 shutdown via timeout
804148: Remote Door Unlock (RDU): Successfully carried out
80414D: Remote Door Lock (RDL): Successfully carried out
8041A6: SPI error body - SPOC
8041A8: Welcome Light repeat lock active
93070C: Error could not be sent after the maximum number of attempts
93071F: Outgoing error message buffer is full
Frontal Light Electronics Left
2 errors
430102: Error could not be sent after the maximum number of attempts
D9D503: Message (V_Veh): Timeout
Frontal Light Electronics Right
2 errors
440102: Error could not be sent after the maximum number of attempts
DA1503: Message (V_Veh): Timeout
Roof function center
6
3 errors
801A0E: NVM_E_INTEGRITY_FAILED
801A20: CAN_E_TIMEOUT
030222: SHD: Automatic initialization process
Camera-based driver assist system
2 errors
5D0036: COM_RX_LIMITED
5D0037: EyeQ2 reset (triggered by watchdog)
Gear selector switch
5 errors
5E1003: Outgoing error message buffer is full
5E1004: Error could not be sent after the maximum number of attempts
8026BD: CANIF_E_STOPPED
8026A1: CANNM_E_NETWORK_TIMEOUT_0
5E1002: Message (vehicle status, 0x3A0) is missing
Instrument panel
7 errors
B7F67C: Combined: CAN input buffer, data loss
B7F669: Combination: information error 1
B7F66B: Combination: information error 3
E12C2F: Interface HU (acknowledgment request combination, 0x172): signal faulty
E12C30: Interface HU (Status Service Call TeleX, 0x30F): signal faulty
E12C3C: Interface DME, DDE (status of engine fuel consumption, 0x2C4): Signal invalid
E12C4A: Interface HU (forecast route destination, 0x3C7): signal invalid
Telematic Communication Box
7
12 errors
610019: NVM integrity check failed
E14405: CAN message timeout GPS_CTI_MOST
E14406: CAN message timeout GPS_PO_EXTS_MOST
E14426: Invalid signal in CAN message GPS_PO_EXTS_MOST
E1442B: Invalid signal in CAN message POWERMGMT_CTR_COS
E1442C: Invalid signal in CAN message STAT_ZV_KLAPPEN
E14412: CAN message timeout LAMP STATE
E14413: Timeout of CAN message STAT_GANG_RUECKWAERTS
E14414: CAN message STAT_ZV_KLAPPEN exceeded time
E14437: Invalid signal in CAN message GPS_PO_MOST
E14438: Invalid signal in CAN message MILEAGE
610026: NAD software reset
Headunit High
1 error
101715: Positioning over 10 minutes not possible
Integrated automatic heating / air conditioning system
3 errors
078022: Message (vehicle status, 0x3A0) is missing
07802B: COMM_E_NET_START_IND_CHANNEL_0
078043: LINIF_E_RESPONSE